In December 2021, we received an inquiry from Mr. Hairun in Malaysia. Mr. Hairun is a mattress manufacturer in need of producing rebonded foam. He had limited knowledge about machine usage and selection and had no prior experience with the production process. Therefore, he required guidance from experts who could assist him from the ground up.



We systematically explained the principles of foam production to Mr. Hairun, along with the necessary materials and equipment. We also took him on a tour of our factory to provide a clear understanding of the entire production process.



After understanding Mr. Hairun's preferences for the rebonded foam, including density, softness, and market prices, we offered him the most suitable foam production solution. We also provided him with information on foam production costs and compared raw material prices for his reference.



Based on the client's needs, budget, and existing factory layout, we devised a cost-effective machine configuration and layout plan for his facility, including an assessment of startup costs.



Once the machines were successfully installed, our team of engineers provided Mr. Hairun with one-on-one foam production training. When he successfully produced the foam he desired for the first time, he called us and said, "I am happy with crying, thank you very much!" Afterward, he purchased a batch foam machine from us and continued to reorder foam chemical materials from our company.

PLC (Programmable Logic Controller)

It is an automatic control device with instruction memory, digital or analog I/O interfaces; primarily used for logical, sequential, timing, counting, and arithmetic operations with bit operations; used to control machines or production processes.



Variable Frequency Drive (VFD)

A VFD is a control device that transforms power frequency from one frequency to another using the on-off action of power semiconductor devices.

The main circuits of a VFD can generally be divided into two types:

- Voltage type: Converts DC voltage from a voltage source to AC in the VFD, with capacitor filtering in the DC circuit.

- Current type: Converts DC current from a current source to AC in the VFD, with inductor filtering in the DC circuit.



Photoelectric Switch

It utilizes the obstruction or reflection of an infrared light beam by a detected object, detected by the synchronous circuit, to determine the presence or absence of the object. It can detect any object that reflects light, not limited to metals.

A mirror-reflective photoelectric switch is used on the vacuum perforating machine.



Heat Exchanger System

Controls the temperature of raw materials in the system to meet requirements.

As the temperature of the raw material rises after passing through the heat exchanger, its viscosity increases. To ensure the normal operation of the high-pressure pump, a special feeding pump is required. Specific requirements are calculated based on flow rate and raw material viscosity.

The temperature control of the heat exchanger should be near the mixing head, correlating the raw material temperature with the switch of the cooling water to automatically control the flow of cooling water to cool the raw material.



Perforating Machine

There are roller perforating machines, vacuum perforating machines, and brush perforating machines, with roller machines having the best control effect, followed by vacuum perforating machines, and brush perforating machines being the worst. Currently, brush perforating machines are rarely used.

The purpose of perforating is to prevent product deformation.

The roller perforating machine controls the size of the gaps. If the gaps are too large, the perforating effect is not good; if the gaps are too small, there will be obvious pressure marks on the product.

There are two methods of perforating: 1. Chemical method - using perforating agents, 2. Mechanical method - using perforating machines.

Products must be perforated as soon as they come out of the mold. Some products may expand after being demolded, and at this time, they should be left for a period before perforating.



TPR

It can prevent product shrinkage and collapse of bubbles; its most basic function is effective perforating to facilitate demolding. However, it can also lead to fluctuations in ILD (Indentation Load Deflection); TPR directly affects the rise speed of the foam.



Loop Pressure Regulating Valve

It is crucial for balancing system pressure in the control system and should be placed as close to the nozzle as possible. If it is far from the nozzle, pressure fluctuations may occur, leading to system instability and unstable products.

The production of block-shaped soft foam typically utilizes the batch foam machine foaming process, a gap-type production method. This method evolved from manual foaming in laboratories. The process involves immediately pouring the mixed reaction materials into an open mold resembling a wooden or metal box, hence the name "boxed foam." The molds (boxes) for boxed foam can be rectangular or cylindrical. To prevent the foam block from forming a domed top, a floating cover plate can be placed on the top of the foam during foaming. The cover plate stays closely attached to the top of the foam and gradually moves upward as the foam rises.



The main equipment for boxed foam production includes: 1) Electric-mechanical stirrer, mixing barrel; 2) Mold box; 3) Weighing tools such as scales, platform scales, measuring cups, glass syringes, and other measuring devices; 4) Stopwatch for controlling mixing time. A small amount of mold release agent is applied to the inner walls of the box to facilitate easy removal of the foam.



The advantages of producing soft foam using the boxed foam method include: low equipment investment, small footprint, simple equipment structure, easy and convenient operation and maintenance, and flexible production. Some small and underfunded domestic and township enterprises use this method to produce polyurethane soft foam. Boxed foam molding is a non-continuous production method for soft foam, so the production efficiency is lower than continuous methods, and the equipment is mostly manually operated, resulting in higher labor intensity. Production capacity is limited, and there is a greater loss in cutting foam plastics. The process parameters for boxed foam should be controlled within a certain range because even with the same formula, the foam properties may not be the same when different process parameters are used. The raw material temperature should be controlled at (25±3) degrees Celsius, mixing speed at 900 to 1000r/min, and mixing time at 5 to 12 seconds. The mixing time of the polyether and additives mixture before adding TDI can be flexibly adjusted depending on the situation, and after adding TDI, a mixing time of 3 to 5 seconds is sufficient, with the key being thorough mixing after TDI addition.



During boxed foam molding, attention should be paid to the following aspects:

1) Prepare before production, including material temperature and machine equipment inspection;

2) Measure as accurately as possible;

3) Control the mixing time appropriately;

4) Pour the mixed material liquid quickly and steadily, avoiding excessive force;

5) Ensure the box is placed steadily, with the bottom paper flat, to avoid uneven material flow during pouring;

6) When the foam rises, gently press the cover to ensure the foam rises smoothly;

7) Additives should be used as specified, and pre-mixed materials should not be left for too long.



Three types of foam equipment have emerged in boxed foam molding. Initially, various raw materials were weighed into a container according to the formula, mixed with a high-speed mixer, and poured into the box mold for foaming and shaping. This method often resulted in residue in the mixing container. An improved method used a metering pump to transport the raw materials to the mixing barrel for uniform mixing. A mechanical device automatically closed the bottom of the barrel, and compressed air was used to press the material into the foaming box for shaping. Both of these methods could create eddies due to the rapid influx of materials into the box, which might cause defects or depressions in the foam products. The most reasonable boxed foam device is to place a bottomless mixing barrel directly in the center of the foaming box. A metering pump delivers the various raw materials needed for foaming into the mixing barrel. After mixing for a few seconds, the lifting device raises the mixing barrel out of the foaming box, allowing the foaming material to flow smoothly over the entire box bottom. This prevents foam cracking due to material eddies, and ensures relatively uniform height throughout the foam.



A pressure device can be added to the expanding foam material to produce flat-topped foam, reducing waste during cutting. This device is suitable for the production of polyether-type polyurethane soft foam and high rebound soft block foam. For polyvinyl acetate polyurethane blocks, this method cannot be used due to the high viscosity of the material, and continuous methods are generally employed.

Calculation of foaming distance for continuous foaming machine



Given: Bubble release time for the formula is 108 seconds, conveyor belt speed during foaming is 4.6 meters per minute. Calculate the swinging and trough foaming distances.

Foaming distance when swinging: (108/60) x 4.6 = 8.28 meters

Foaming distance when troughing: [((108-18)/60)] x 4.6 = 6.9 meters



Explanation: For the same formula, continuous foaming machine has a shorter bubble release time than small bubbles. The calculated foaming distance is shorter than the actual foaming distance. This method only provides approximate confirmation of the foaming distance, supporting the adjustment of the settling plate. Troughing: 18" indicates the time in seconds that the raw material stays in the overflow trough.



Calculation of foaming height for continuous foaming machine



Given: Formula flow rate: 80 kilograms per minute for polyether, 20 for white polyether, 60 for TDI, 20 for stone powder, conveyor belt speed 4.5 meters per minute, mold width 1.65 meters, producing foam with a density of 25 kilograms per cubic meter. What is the foaming height in meters?

Total formula weight: 80 + 20 + 60 + 20 = 180 kilograms

Formula volume: 180/25 = 7.2 cubic meters

Base area of conveyor running per minute:

4.5 x 1.65 = 7.425 cubic meters

Foaming height: 7.2/7.425 = 0.97 meters



Explanation: Silicone oil, amine, and tin are not considered here as they offset the amount of carbon dioxide used during the foaming process. Moisture content (MC) is not considered because MC does not increase foam weight when vaporized.



Foaming Daily Operation

Beginners worry that improper adjustment of the settling plate will cause the liquid sprayed from the nozzle to surge forward or backward, affecting foaming. The reaction rate gradually increases within the first two minutes after starting the machine, sometimes requiring corresponding adjustments to the settling plate. Adjustments to the settling plate are more critical in formulas with low density and high MC.

TDI flow rate can be calculated by determining the corresponding scale value for the flow rate, but it is recommended to measure the TDI flow rate during the first foam production. Flow rate is too important; if the flow rate is incorrect, everything else will be a mess. It's best to rely on the simplest and most intuitive method of measuring flow rate.

When powder is being mixed, the mixed stone powder should be left overnight and production should start the next day. For formulations containing melamine and stone powder, it is recommended to first mix the melamine with the polyether for a period of time before adding the stone powder.

Formulas for foam machines with longer mixing chamber or more teeth on the mixing shaft typically have less amine and lower material temperature. Conversely, formulas for foam machines with shorter mixing chamber or fewer teeth on the mixing shaft typically have more amine and higher material temperature.

For the same formula, when switching between dual spray swing heads and single spray swing heads, if the cross-sectional area of the two nozzles is similar, the requirements for the fineness and number of layers of the mesh are similar.

Correction of small material flow rate can be done by measuring the return flow rate of the small material, or by dividing the total usage by the foaming time for correction. When the values obtained from the two correction methods differ significantly, the data from the second correction method should be used.

Formulas for soft foam with better properties are usually in an unstable range, such as lower TDI index, lower water to MC ratio, lower T-9 dosage, and lower silicone oil dosage. Just like in our jobs, there must be effort before reward.

How to properly control the tension of the upper thread?

When removing the thread, be sure to pass through the thread clamp on the upper thread clamp. The thread clamp cannot be adjusted too tight. When you need to adjust the tightness of the upper thread, you cannot pull the upper thread directly. You must control the tightness of the upper thread through the thread clamp on the control device; when adjusting, it should not be too tight or too loose, and there should be no jamming, otherwise it will cause jumpers. Or disconnected.



How to draw a pattern?

When drawing a pattern for a quilting machine, we can use professional pattern drawing software, but the exported format must be HFP. How to enlarge or reduce the size when drawing a floral pattern? In "Edit Pattern", open "Scale Entire Pattern", and based on our needs, click on the pop-up box's "millimeters" or "inches" option, then add the X and Y parameters according to our needs, and click "OK" after entering.



How to troubleshoot the cause of abnormal noise in a quilting machine?

First, check whether the frequently worn parts are lacking oil, and add some machine oil or grease to the dryer areas; then check whether there is any clearance in the bearings of various components; also carefully observe whether the accessories and wear parts are excessively worn, and replace them timely if discovered.